Month: July 2024

Major purge…

I’ve been doing some serious house cleaning lately. This was partially in preparation to live in an RV in the not too distant future.

First, I got rid of all my computers and traded in my 11-inch iPad Pro on a new 13-inch iPad Pro. This new 13-inch iPad Pro will be my main computing device. I’ve kinda done this before as an experiment. So I already know what to expect. This time it is more out of necessity. But, I am leaving open the possibility that I could pick up a MacBook Air. I’d really like to make the iPad-only thing work though. Technically, we still have a Windows laptop. But it doesn’t really count. It only gets used when there is no other way to get something done.

Second, I cleaned out virtually all of my unneeded ham gear. I’ve been selling stuff left and right. What I have left is about six handhelds and one desktop radio. The desktop radio is the ICOM IC-7100. So I will use that for repeaters and the occasional HF work. The handhelds will be used with my openSPOTs and my Allstar nodes.

As part of my “shack cleansing” I sold my WiRES-X node. I gave away the desktop computer it ran on to a co-worker. I had two co-workers that were interested. So we flipped a coin.

I also decided to sell all my ZUMspot-USB sticks. This will remove the indecision where I’ve occasionally switched back and forth between the Raspberry Pi hotspots and my openSPOTs. No more switching. Not sure what I’m going to do with the six Pi 400s that I was using with these ZUMspot-USB sticks. Probably just Goodwill them.

As I was picking through my stuff to sell things… I came across my Alinco 70cm monoband radio. And I got to thinking. Why don’t I put my IRLP node back up? Of course I won’t be running an IRLP node in the RV. But I might as well run it until that time comes. Just for fun. So… the AI7HL IRLP node is back up and running!

It’s not just ICOM

My last post was a little harsh toward ICOM. After thinking more about this, I realized the Yaesu FT-991A has a different but very similar problem. The fact is, neither the IC-7100 or the FT-991A are good for use with digital voice hotspots, if you are going to use them with repeaters at the same time.

As previously discussed, the drawback with the IC-7100 is… the level of mic gain that is suitable for regular FM repeater work is totally unsuitable for D-Star use. So trying to use the radio with both regular FM repeaters and D-Star hotspots requires a ton of knob twisting to adjust the mic gain back and forth every time you change what you’re doing. This is because there is a single stored mic gain setting for the entire radio. All they would need to do is store separate settings for each mode and the problem would be solved.

A similar drawback with the FT-991A is… the power level setting is not stored with the memory channel info. So whatever your power level is set to, it applies to all memory channels. This means extensive knob twisting to move the power level from one end of the scale to the other every time one switches between a repeater and a local hotspot. I guess we’re all spoiled with the newer Yaesu radios where each memory channel has its own stored power level.

The IC-7100 doesn’t store the power level with the memory channel info either. But at least it is stored separately for each band. So… that technically works if all your hotspots are UHF and most of the repeaters you work are VHF.

All this being said, the answer to these problems is EASY. I cannot believe I didn’t see it sooner. If one uses a handheld for their local hotspots, then none of these aforementioned problems really matter. To be clear… I think there are obvious problems with some of the design decisions made for both the IC-7100 and the FT-991A. But the level of impact these have totally depends on your use case. And there is probably a good reason why virtually no one I’ve spoken with has really understood what I’m griping about. They simply aren’t using their radios the way I want to use mine.